Water level sensor troubleshooting
This page helps when pairing the sensor doesn’t go through, or when the sensor later stops measuring. What the light means is on the Setting up the water level sensor page.
The app can’t find the sensor, or the light stopped blinking
Section titled “The app can’t find the sensor, or the light stopped blinking”The app shows Looking for your water level sensor and after a while offers Nothing yet?. If the light isn’t blinking orange, the pairing time has run out. Unplug the charger and plug it back in. Once the light blinks orange briefly, the sensor is ready for another try.
The light doesn’t come on at all
Section titled “The light doesn’t come on at all”If nothing lights up when you plug in the charger, check that the charger and the cable work.
The light is steady and doesn’t blink
Section titled “The light is steady and doesn’t blink”The sensor is charging and the colour shows its battery level. It’s most likely already paired. Look on the Overview screen to see whether the sensor is there. If it isn’t, the sensor is paired with another Hub. Reset it to factory settings as the section “You want to reset the sensor to factory settings” below describes.
Pairing takes long or ends with an error
Section titled “Pairing takes long or ends with an error”The app says pairing is taking longer than usual, or shows Pairing didn’t finish. Unplug the charger and plug it back in. Once the light blinks orange briefly, select Try again.
If pairing keeps failing, restart the Hub. Unplug it from the socket, plug it back in and try pairing again.
Calibration didn’t finish
Section titled “Calibration didn’t finish”The app shows Calibration didn’t finish. The sensor didn’t complete the calibration, so its readings may be off. Check that it’s firmly mounted, points straight down at the water and has nothing below it.
Then measure the current water level from the bottom precisely again and select Calibrate again, or Try again in the setup wizard. The sensor calibrates the next time it reports in.
The water level doesn’t show in the app
Section titled “The water level doesn’t show in the app”What to do depends on what the app shows for the sensor:
- Setup incomplete: select Finish setup and complete the mounting and the tank measures. Until you finish setup, the app doesn’t show the level.
- Calibration in progress: the level appears the next time the sensor reports in.
- Waiting for first reading: the sensor measures only while it’s off the charger. If it’s on the charger, unplug it.
If the sensor shows Delayed or Offline, it hasn’t reported for a while. Follow the next section.
The app says the sensor isn’t responding
Section titled “The app says the sensor isn’t responding”When the sensor hasn’t reported for 24 hours, every member of the Hub gets a push notification and an e-mail. The sensor’s screen shows Water level sensor not responding.
First check that the Hub is online, because without it no readings arrive from any module. How to check is on the Hub troubleshooting page. Then check the sensor’s battery and charge it if needed. If the connection is weak, move the Hub closer to the tank. Once the sensor reports again, you get a message saying “Water level sensor responding again”.
The water is just below the sensor, or the sensor is under water
Section titled “The water is just below the sensor, or the sensor is under water”The sensor’s screen shows Water just below the sensor or Water level sensor probably under water. The water has risen almost to the sensor. The sensor’s signal can’t get through water, so a flooded sensor sends no readings.
Check that the tank overflow isn’t blocked, or empty the tank. Once the level drops, the sensor reports again on its own. If the water often reaches the sensor, mount it higher, at least 15 cm above the overflow. Then calibrate it again as described in The sensor isn’t where it was during setup.
The app reports a low battery
Section titled “The app reports a low battery”When the battery drops to 20%, every member of the Hub gets a push notification and an e-mail. The sensor’s screen shows Low battery.
Charge the sensor on its charger. It doesn’t measure while charging. When the battery is at 90% or more, the light is steady green. Then put the sensor back in the same position. If its position has changed, calibrate it again as described in the next section.
The sensor isn’t where it was during setup
Section titled “The sensor isn’t where it was during setup”If the sensor has shifted, tilted or moved somewhere else, its readings no longer match the tank. Fix it firmly, pointing straight down at the water. On the sensor’s screen, open Calibration and measure the distance from the bottom to the sensor and the current level again. Enter them and select Calibrate. The sensor calibrates the next time it reports in.
The light blinks red
Section titled “The light blinks red”If the light is steady red while charging, the battery is just below 30%.
If the light blinks red slowly, the charger has been plugged in quickly for the third time in a row. Plugging it in again while it blinks resets the sensor to factory settings. If you don’t want that, leave the charger plugged in until the light stops blinking.
If the light blinks red five times quickly, the sensor has left the Hub and reset to factory settings. What to do next is in the following section.
You want to reset the sensor to factory settings
Section titled “You want to reset the sensor to factory settings”You reset the sensor with its charger, without the app. It helps when the sensor is paired with another Hub, or when it still considers itself paired after you removed it in the app. It’s also the last resort when the sensor has lost its link to the Hub and nothing in the sections above helped.
It works only on a paired sensor. Keep the charger plugged in for less than 20 seconds each time, or the sensor starts counting the plug-ins again from the beginning.
- Plug the sensor into its charger. The light blinks blue three times.
- Unplug the charger, wait about 10 seconds and plug it back in. The light blinks blue three times again.
- Unplug it, wait about 10 seconds and plug it in a third time. After a moment the light starts blinking red slowly.
- While the light blinks, unplug the charger. Wait about 10 seconds and plug it in a fourth time. After a moment the light blinks red five times quickly, and the sensor resets to factory settings.
- Leave the charger plugged in. Once the light blinks orange briefly, the sensor is ready to pair.
If the light doesn’t blink red slowly after the third plug-in, leave the charger plugged in for at least half a minute. Then unplug it, wait about 10 seconds and start again from the first step.
The sensor forgets its Hub and its settings. It keeps its serial number. If you still see the sensor in the app, first remove it on its screen with Remove module. Then add it as the Setting up the water level sensor page describes.
If none of this helps
Section titled “If none of this helps”On the Help screen in the Hastr app, select Report a problem and describe what happened and what hasn’t helped.
Made in EU